Chords the Sticks Are Woven in the Spokes Again
There are 12 bolts on the standard Mira and Fanny loom (6 on each side) and the distance between the outside of the frame and the edge of the hole where the nut is installed should be about iv to 4 ane/four inches. The bolt locations on a single side of each loom (Mira left, Fanny right) are shown in the pic below (Click to enlarge). On the 4 shaft Nilus and Nilus II Jack looms, 4 of the Nilus Long Bolts are used to attach the lateral cross-members to the castle.
These bolts are used to spike the horizontal Batten Handtree and Batten Sley to the vertical Swords on each side of the loom beater. At that place are a full of four bolts. The 2 lower bolts have square nuts and are always kept tight to position the beater frame. The 2 upper bolts take wing nuts that face the weaver and are loosened to heighten the Batten Handtree so the Reed can exist removed and installed.
The smaller bolts are used on the Meco table loom (pictured left) and the larger are used on the Artisat, Mira, Fanny, Nilus, Nilus Ii, Colonial and about other Leclerc Floor looms.
| Detail # | Label | Clarification | Cost (each) |
| 88800-0282 | A | Meco Beater Bolt Set (4 x Bolts/Washers/Nuts) | $13.l CDN $11.95 US |
| 88800-0283 | B | Flooring Loom Beater Bolt Fix (4 ten Bolts/Washers/Nuts) | $xv.75 CDN $13.95 US |
Treadle Gear up Mounting Bolts
These bolts are used to fasten the metal brackets of the treadle fix to the lower frame beam of most Leclerc floor looms like the 4 shaft Mira, Fanny and the four shaft Nilus. A set of two bolts is provided, each with a square nut. Note that these but work for the curved set of vi treadles with the metal mounting brackets. Dissimilar bolts are required for the wooden mounting brackets used in the 8 shaft Nilus and all Nilus 2 models. Contact us for pricing on the bolts for other models.
| ITEM # | DESCRIPTION | PRICE (each) |
| 88800-0284 | Treadle Set up Mounting Bolts - Metallic Bracket (two x Bolts/Basics) | $5.50 CDN $4.95 US |
| 88800-0224 | Treadle Prepare Mounting Bolts - Wood Subclass (2 x Bolts/Basics) | $six.l CDN $5.95 US |
Colonial Frame Pegs
These wooden pegs are used to hold the frame together on the original Colonial loom. They are normally tapped in identify with a safety hammer and hold the frame securely even when the loom is beingness browbeaten heavily. Note that these pegs are not used in the other versions of the Colonial like the Colonial I and the Colonial v2 which use bolts to concord the frame together.
These pegs are fabricated from Maple Hardwood and 8 pegs are used on the Colonial loom. (Click to enlarge).
| ITEM # | Clarification | Cost (each) |
| 88800-0245 | Colonial Frame Peg | $seven.00 CDN $6.00 The states |
Beater Sword Mounting Plates
These metal plates are used to attach the wooden beater swords to the loom frame on floor looms like the Fanny, Mira, Nilus, Nilus II and Colonial. They allow the beater height to exist adjusted past virtually one inch to make sure the beater is positioned properly in relation to the warp threads. By loosening the pair of nuts on each side, the wooden sword can be moved up or downward. The kit includes 2 of the mounting screws too as the bolts/nuts used to spike the plate to the wooden sword. The screws to attach the mounting plates to the loom frame are also available separately.
A prepare of lag screws to attach the plates to the frame are also included but in newer looms a set of bolts/nuts bolts may exist required. Contact us if these are required.
Note that older Leclerc looms had beater mechanisms that did not accept this aligning plate but they can be upgraded by cut off the end of the swords and drilling a set of holes to attach the plate and using the shorter lag spiral included. Come across the flick shown hither for measurements.
Some older Leclerc floor looms used a slightly different version of this plate. The pic located hither includes measurements to make up one's mind if the plate volition piece of work with these looms.
| ITEM # | DESCRIPTION | PRICE |
| 88800-0068 | Beater Sword Mounting Plate Set | $48.00 CDN $44.00 US |
| 88800-0069 | Beater Sword Mounting Spiral/Washer Set (two Screws and 4 Washers) | $v.00 CDN $four.l United states |
Treadle Set Lock Nut
On most Leclerc floor looms like the Fanny, Mira, Nilus and Nilus 2 the treadle set is mounted using two brackets which attach to the frame. The metal treadle rod is fastened to the bracket on one side, merely just fits through a pigsty in the other side to allow the treadle parts to be removed. To go along the rod from coming out of the bracket, a flat metal lock nut is inserted on the exterior end of the treadle rod and pushed in until it is up confronting the subclass. This lock nut is designed to motility only one fashion and tin can not normally be removed without destroying information technology. To re-install the wooden treadles and spacers after taking the treadle set apart, another flat lock nut is commonly required. The part numbers below are for a single Treadle Lock Nut.
The standard lock nut fits most looms including the Artisat, Minerva and Tabular array loom Treadle Stands. A special smaller Lock Nut is used on the Meaty and 4 are required as they are used to secure the Restriction Treadle as well as the shaft treadles. Specify the specific loom with the order notation section to ensure you get the correct size.
Note: The erstwhile lock nut can normally be removed by prying the space between the nut and the bracket using a large screwdriver or cut one side of the nut with a pair of pliers.
| ITEM # | Clarification | Cost (EACH) |
| 88800-0197 | Treadle Fix Lock Nut | $i.75 CDN $i.50 US |
| 88800-0198 | Compact Treadle Set Lock Nut | $1.75 CDN $one.50 U.s.a. |
Chest Beam Pins
These metal pins are used on most Leclerc Floor looms to attach the front and back chest beams. They come in pairs and fit most of the looms with removable breast beams similar the Fanny, Mira, Nilus, Nilus II, Nilart, Colonial and Weavebird.
They also fit the brackets for the older model of the Double Warp Beam that used a standard breast beam instead of the current roller design. Normally a total of 2 pairs (iv pins) are used on each loom.
| ITEM # | Clarification | PRICE (pair) |
| 88800-0268 | Pair of Breast Beam Pins (2 Pins) | $v.95 CDN $4.95 U.s. |
Floor Loom Treadle Prepare Parts
The parts are used to construct and adhere the Treadle sets for the Fanny, Mira, Nilus (front swivel) and Nilus 2 (front hinge) floor looms. These parts may also be used on some older versions of the Table Loom Treadle Stands.
The Fanny, Mira, Nilus (4 Shaft Front-Swivel) looms use a treadle set made using 1 x Left Metal Bracket with an attached curved treadle rod (C), i x Right Metallic Subclass (D), six x Treadles (A), 5 x Spacers (B) and 2 x Metallic Washers (J). The Full Treadle Gear up for these looms can be ordered using Part Number 88800-0271 below. The Mounting Bolts (E) are used to attach them to the Loom Frame. This treadle fix is shown at the top of the pictures
The Treadle Set for the 4 shaft Front Swivel versions of the Nilus II is constructed with 6 ten Treadles (F), 4 x Spacers (B), 4 x Washers (J), i x Treadle Rod (G) and 3 x Mounting Brackets (H). This Treadle Fix is shown at the bottom of the pictures.
| ITEM # | SHOWN Equally | DESCRIPTION | LOOM | PRICE (each) |
| 88800-0258 | A | Single Wooden Treadle | Fanny, Mira and Nilus (front swivel) | $69.95 CDN $62.95 The states |
| 88800-0255 | B | Wooden Treadle Spacer | Fanny, Mira, Nilus (front swivel) and Nilus 2 (front end hinge) | $3.50 CDN $2.95 U.s. |
| 88800-0278 | C | Left Treadle Mounting Bracket with Treadle Rod and Lock Nut | Fanny, Mira and Nilus (front swivel) | $49.95 CDN $44.95 US |
| 88800-0277 | D | Right Treadle Mounting Subclass | Fanny, Mira and Nilus (forepart hinge) | $34.95 CDN $31.50 US |
| 88800-0284 | E | Treadle Set Mounting Bolts - Metal Brackets (2 x Bolts/Nuts) | Fanny, Mira and 4 shaft Nilus (front swivel) | $5.50 CDN $four.95 The states |
| 88800-0224 | - | Treadle Fix Mounting Bolts - Wood Brackets (2 x Bolts/Basics) | 8 shaft Nilus (front hinge) and all Nilus 2 (front end-swivel) | $half dozen.50 CDN $5.95 U.s.a. |
| 88800-0259 | F | Single Nilus II Wooden Treadle | Nilus II (4 shaft forepart hinge) | $49.95 CDN $44.95 US |
| 88800-0276 | One thousand | Nilus II Treadle Rod (with 2 Lock Nuts) | Nilus II (four shaft forepart hinge) | $xvi.95 CDN $15.25 US |
| 88800-0279 | H | Single Nilus II Wooden Treadle Mounting Bracket with Mounting Bolt (three needed) | Nilus II (front hinge) | $29.95 CDN $26.95 The states |
| 88800-0256 | J | Metal Treadle Washer | Fanny, Mira, Nilus (front swivel) and Nilus II (front hinge) | $0.35 CDN $0.thirty Usa |
| 88800-0271 | Full Fanny/Mira/Nilus Treadle Set | Fanny, Mira and Nilus (iv shaft) | $494.95 CDN $444.95 US |
Bergere 2nd Heddle Support
This kit adds a second set of heddle support bracket to the Leclerc Bergere Rigid Heddle loom to allow two rigid heddles to be used while weaving. The brackets are mounted in front of the existing ones and a set of screws is provided alonge with mounting instructions. The kit includes a bracket for each side and instructions are shown in the Bergere department of our Manual page.
| Item # | DESCRIPTION | PRICE |
| 88800-0197 | Bergere second Heddle Support Bracket Fix | $42.00 CDN $xl.00 Us |
Loom Frame Parts
Nosotros only list a minor selection of the parts available for Leclerc looms on this site but we tin can besides provide a very large number of forest and metal parts that make up the frame and operating machinery of most loom models. These 18-carat Leclerc quality components include things similar lamms, frame beams, treadles, warp and cloth beams, counterbalance rollers, breast beams, beater swords and sleys, folding back beam supports and much, much more. (Click on the moving picture to the left to expand)
Contact us at nmanners@camillavalleyfarm.com and we will try to assist. Note that it often helps for usa to have clear pictures of your loom to identify the specific model and version and avoid providing the incorrect product. Our Leclerc Loom Identification Page will help y'all decide the specific model.
More PARTS (folio ii) Notation that these pages comprise only a small-scale selection of parts available for Leclerc weaving looms.
If y'all require a part non shown on this or whatsoever other page on our site, please contact us and nosotros will assistance yous locate what you crave!
 | NEED Help? Contact us for assistance in answering questions about these products or for aid recommending a loom matched to your weaving level and needs. See our Leclerc Loom Comparison Nautical chart for more assistance in deciding which loom is correct for you. |
| How to Order: Orders may be placed using our secure Online Order Form (this course should open up in another window). Click Here for more data on how to place an society besides as our terms and weather condition. Payment/Currency: Payment tin be made using VISA or Mastercard, Cheque or Money Society in United states or Canadian funds. The states credit carte purchases are billed direct in US funds eliminating whatsoever foreign currency conversion charges past the credit card company. Product Directories If yous are looking for other items on our website, try using our product directories to quickly find what you are looking for! Our products are grouped as follows: Weaving/Spinning Product Index Books, Magazines & Videos. | Price/Shipping Quote? If yous would like an exact quote for any items complete with shipping costs, please phone call or email us at nmanners@camillavalleyfarm.com with you location and we will provide this. Gift Certificate If you are looking for a gift for a Knitter or Weaver and can't figure out what they want, a Camilla Valley Farm Gift Certificate is an excellent fashion to ensure you become the perfect gift! We can also e-mail gift certificates if you are running out of time! Latest News/Updates Go along upward to date with what is new at Camilla Valley Farm past following us on Instagram! (Click on the logo below)  |
Last Updated: Thursday March 24th, 2022
Source: https://www.camillavalleyfarm.com/weave/loomparts3.htm
0 Response to "Chords the Sticks Are Woven in the Spokes Again"
Enregistrer un commentaire